Hydraulic Hose Ferrule Design
Ferrules are the elements used to assemble the hydraulic fittings on hydraylic hoses for high pressure. They are specially designed for rubber hydraulic and thermoplastic hoses and amply used as well in industrial hoses. Ferrules are assembled on crimping machines for a permanent connection or by screwing in the case of reusable ferrules. According the way the fittings are assembled on the hose, we distinguish the types of two-piece crimp fittings, that is ferrule and insert or one-piece fitting, this one displayed in the fittings chapter.
Fittings for high pressure hoses are assembled on hydraulic hoses with the use of special ferrules. Designed especially for rubber hydraulic hoses and thermoplastic hoses but widely used for industrial hoses as well. Assembled by screwing (reusable) or on crimping machines (permanent connection).Hydraulic hose ferrules are essential components of the hydraulic hose assembly system; they fasten the hose fitting at the end of the hydraulic hose tightly, and it assure hydraulic hose assembly work well under the working pressure.
Our permanent crimp sleeves are typically used in applications where a safe, more durable and reliable clamping method is preferred over band clamps or strapping. When installed properly, the sleeve provides a 360° uninterrupted compression around the hose and results in a "clean" attachment with no protrusions.
The sleeves have smooth, beveled edges and are available in stainless steel or zinc plated carbon steel. They are to be installed with a hydraulic crimper and can be used on most hose shank couplings on the market.
Sleeves/ferrules are chosen based on the length of the coupling barb and the actual hose outside diameter (sleeves must fit snug over the cover of the hose prior to crimping). As a general rule, the sleeve/ferrule should be about 1/4" shorter than the barb - if the sleeve/ferrule is longer than the barb it will start to compromise the cover/structure if the hose is bent near the coupling, and if the sleeve/ferrule is too short then the barb will dig into the tube and lead to premature failure - therefore it is important to choose the proper length. SPECIAL NOTE: As with hose and couplings, crimp sleeves are subject to maximum pressures, temperatures, and mechanical forces like end-pull. As a rule, the higher the temperature, the lower the maximum pressure rating for crimp sleeves.
Hydraulic Hose Ferrule PDF.
Hydraulic hose ferrules are essential components of the hydraulic hose assembly system; they fasten the hose fitting at the end of the hydraulic hose tightly, and it assure hydraulic hose assembly work well under the working pressure.
Sinopulse Hose Factory Co., Ltd. is a leading company in manufacturing high pressure hoses and our products are sold very well both at home and abroad. High pressure hoses - the most important part of modern equipment, are widely used for all hydraulic systems, gas and water supply to deliver fluids under pressure (oils, fats, emulsions and others).
Hoses are made of different materials with different technologies depending on the operating environment, limiting pressure, climatic conditions and the fluids that they convey. Our high pressure hose products give the best solutions for customers to solve the fluids problems in hydraulic systems.We hydraulic hose manufacturer provide low pressure hydraulic hose and high pressure hydraulic rubber hose,Choose us, you can be get most careful and thoughtful service, contact one piece fittings manufacturer.
More Hydraulic Hose Ferrule Products Specification:
Hydraulic Hose Ferrule 00TF0 and Hydraulic Hose Ferrule 00018 and Hydraulic Hose Ferrule 01400
More Hydraulic Hose Ferrule:
More Hydraulic Hose Ferrule Products Specification:
Hose Ferrule 00018 and Hydraulic Hose Ferrule 00401
More Hydraulic Hose Ferrule:
Hydraulic Hose Ferrule Application:
Application: widely used in the hydraulic and fluid conveying system of machinery, oilfield, mine, building, transportation, food and other industries.
Payment Type:L/C,T/T,D/P
Incoterm:FOB,CFR,CIF,EXW
Min. Order:500 Piece/Pieces
Transportation:Ocean,Air
Hydraulic Hose Ferrule Attributes
Model No.: 3/8"-2"
Brand: OEM
place of origin: China
Processing Service: Moulding
Supply Ability & Additional Information
Packaging: Carton
Productivity: 9000 pieces per day
Certificate: ISO9001:2015
Hydraulic Hose Ferrule Features:
* Material: Carbon Steel
* Surface Treatment: Zinc plated
* Salt Spray Test: 96h
